Froster AS | Kvalitet og kompetanse

Kundeservice

T + 47 55 36 58 55
post@froster.no

Døgnbetjent kundeservice

    Industri
    Prosessutstyr
    VVS / VA
    Entrepenør & Landbruk

    Selvsugende sentrifugalpumper

    En selvsugende sentrifugalpumpe er, som navnet tilsier, selvsugende i motsetning til en “vanlig” sentrifugalpumpe. Den kan evakuere sugeledninger opp til 8 meter fra “tørr” tilstand (pumpehuset må fylles med vann før første oppstart). Pumpene er spesielt godt egnet for tømming av kummer, sjøvannsinntak og andre typiske installasjoner der mediet må suges opp, og man ikke ønsker en neddykket pumpe, men en tørrtoppstill installasjon. Den spesielle konstruksjonen gjør dem også velegnet der det er fare for at pumpen i kortere perioder vil jobbe mot en stengt ventil og der det er fare for tørrkjøring da det alltid vil være noe væske i pumpehuset.

    Selvsugende sentrifugalpumper er også egnet hvor det er en høy andel av faste partikler, og mye slitasjepartikler. De selvsugende pumpene brukes i industrien, i forbindelse med avløpsvann, miljøvern, sjøvann, syrevasking, skipsbyggeri, bygningsindustri og kommunal virksomhet.

    Pumpene finnes i en mengde utførelser, forskjellige materialer, elektrisk, hydraulisk, diesel- eller bensindrevet, magnetdrevet, på tralle, bærbar m.m

     

     

     

     

     

    Description

    Recommended for corrosive and/or abrasive & viscous liquids, compatible with cast iron, bronze, aluminum or stainless steel, which can contain air.
    The pump can be located above, on side or under the liquid. Some pump sizes can self-prime up to the physical limit of 8 m.
    Available with various drives such as

    single phase, three-phase, explosion-proof motors and gasoline or diesel engine.
    Produced in different versions depending on the specific application. For example Close coupled, Bi-Block, Classic.

    Also with ATEX Certificate.  

     

    Working Principle


    a-150dpi

    The self-priming pump will evacuate all the air. The vacuum produced as the impeller rotates (2) draws air into (1) the pump where it is mixed with the liquid already contained in the pump casing.
    When all the air has been evacuated from the suction line the liquid is pumped, even if air-laden.

    b-150dpi

    The air/liquid mixture is driven to the discharge side where the air separates out and is expelled through the discharge port (3) while the liquid, due to the higher gravity, falls back and is reused in the suction side through a small passage.

    c-150dpi

    The high suction port keeps enough liquid inside the casing to allow re-priming any time. The check-valve in the suction port (4) avoids a backflow of the liquid and reduces priming time.


    The pump is normally placed dry above or aside the liquid. In this case the suction line contains air. This Video shows how the pump primes the air from the suction line only with some water inside the casing.

     

    Advantages


    • Suction and discharge ports are available flanged or threaded (up to 4”). The threaded port have through-holes to take away faster the pipes.
    • For easy installation, the DIN or ASA flanged ports have through-holes and ¼” threaded hole for Vacuum meter and manometer.
    • Check valve: avoids backflow of liquid from the discharge side and reduces priming times. Available in NBR, Viton® (FKM), PTFE & EPDM.
    • Maintenance-free ball bearings.
    • Mechanical seal in Sic/Viton® (FKM) with stainless steel shaft sleeve and lubrication behind the seal to improve dry running capabilities.
    • Heavy-duty open impeller and wear plate designed for abrasion and passage of solids. On request with cutting device for soft solids.

    Typical Applications


    • Animal food
    • Bentonite
    • Clean or dirty solvents
    • Cooling milk
    • Diesel
    • Fertilizer
    • Fire fighting water
    • Flood drainage
    • Gasoline
    • Light-oil
    • Lime milk
    • Liquid manure
    • Must
    • Petroleum products
    • Rain water
    • River water
    • Soda
    • Sump water
    • Transformation oil
    • Wash fluids
    • Wastewater
    • Water with cutting sand
    • Water with mud
    • Water with sand
    • Water with solids

    …and many more.

     

    Construction


    Stationary


    Close coupled pump

    Bi-Block with flanged ports

    Bi-Block with flanged ports on base plate

    S-Con motore oleodinamico 72dpi

    With hydraulic motor

    Classic, with elastic coupling, guard and B3 electric motor on base plate

    On tank frame


    Mobile


    On carrying frame

    On trolley for flat ground

    On trolley with 2 tractor profile wheels

    On trailer with tank

    On carrying frame for the emergency

    On trailer with tank & 4 wheels for flat ground

    On skid

     

    Options & Spare parts


    Threaded ports BSP-NPT (1″-4″).

    Counter flanges to weld (standard for 6″ & 8″).

    Flanged ports DIN-ASA with ¼” threaded holes for Vacuum-meter and Manometer.

    Wear plates for abrasion.

    Heavy-duty open impeller designed for passage of solids.

    piatti+coltelli

    Impeller & the wear plate with cutter device for soft solids.

    Priming cover.

    Inspection cover.

    Cover with zinc anodes for sea water.

    Non-return valve: avoids a backflow of the liquid from the discharge side and reduces priming times. Available in NBR, FKM, PTFE or EPDM.

    Clean out cover.

    Clean out cover with ball valve.

    Bearing housing with maintenance free ball bearings.

    Mechanical seal available in different materials.

    Automatic grease lubricator (+PS).

    External seal flushing in front of the mechanical seal.

    Metal bellow mechanical seal.

    Seal-less with magnetic coupling.